Switch to desktop version  
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Welcome back to the VXOC FORUM. Sorry for our lack of support over the last year but MYBB is back and so are we. Let's get the forum buzzing again... (March 25, 2022) x



Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Tags
help urgent needed

Urgent help needed
#1
Hi, replaced brakes on front of car and the stud on the hub snapped.
So there's 4 holding wheel on instead of five.
What's the best way to fix this?
Thanks guys


Sent from my iPhone using Tapatalk
Using Tapatalk
Reply
#2
Isn't the stud part of the hub?

if so I would say a new hub is needed or a 2nd hand one.
Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply
#3
Not sure, Google says your can replace them individually but knowing vx is have to change the whole hub. They expensive on a j do you know?


Sent from my iPhone using Tapatalk
Using Tapatalk
Reply
#4
Found the info on TIS mate so hope it helps.

Wheel Stud Replacement


Removal Procedure


1.Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle.


2.Remove the tyre and wheel assembly. Refer to Tyre and Wheel Removal and Installation.


3.Remove the wheel bearing/hub. Refer to Rear Wheel Bearing and Hub Replacement.





4.Release the wheel stud (1) from the bearing hub with the hydraulic press and DISCARD the stud.


Installation Procedure





1.Install a NEW stud into the bearing/hub assembly (2). Add enough washers (3) in order to draw the stud into the hub.


2.Install and tighten a wheel nut (1) until the head of the wheel stud is fully seated against the back of the bearing/hub flange (2).


3.Remove the wheel nut (1) and the washers (3).


4.Install the wheel bearing/hub (2). Refer to Rear Wheel Bearing and Hub Replacement .


5.Install the tyre and wheel assembly. Refer to Tyre and Wheel Removal and Installation .


6.Lower the vehicle.

Printable .PDF below for you.
http://vxoc.org.uk/Images/vxoc%20astra-j...cement.pdf
Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply
#5
Brill thanks rusty


Sent from my iPhone using Tapatalk
Using Tapatalk
Reply
#6
richje100 Wrote:Brill thanks rusty


Sent from my iPhone using Tapatalk

No problems mate, you might be able to whack it out with a nice hefty lump hammer.


Sent from my iPhone 5c using Tapatalk.
Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply
#7
Fingers crossed.


Sent from my iPhone using Tapatalk
Using Tapatalk
Reply
#8
Rusty, any idea of the size of the bolts? Found http://pages.ebay.com/link/?nav=item.vie...0541841245



Sent from my iPhone using Tapatalk
Using Tapatalk
Reply
#9
I know mine is a STUD, M12, WHEEL TO HUB Part number 9599302 Autovaux charge £2.21 so I can't see it being much dearer from a dealer and they would get it in quicker.
Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply
#10
Local dealer £2.57 each. Happy days.


Sent from my iPhone using Tapatalk
Using Tapatalk
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
SVS help needed again!!! hooper 6 4,429 20:th-Dec-2019, 13:57:40
Last Post: Big Dave2
  New Engine Needed ? Breengin 19 8,629 14:th-Mar-2019, 08:48:57
Last Post: Rusty2009
  A little knowledge needed please Sri~mike 4 3,788 11:th-Mar-2019, 01:33:41
Last Post: Sri~mike
  coolant tank hose ref needed alexy357 1 2,750 4:th-Mar-2019, 08:43:32
Last Post: Rusty2009
  URGENT HELP NEEDED!!!! Michael T18 7 4,933 17:th-Sep-2018, 14:07:50
Last Post: Michael T18
  Alternator part code needed for astra gtc j 2014 cdti 2.0 king 4 5,422 20:th-Apr-2018, 09:01:30
Last Post: king
  Part numbers needed Daniel199025 5 5,039 15:th-Sep-2017, 13:48:20
Last Post: Daniel199025
  GTC body kit, color advice needed twinpipes 3 5,256 5:th-Aug-2017, 12:03:36
Last Post: gregj
Little help needed Jon3sy 8 6,218 29:th-Jun-2017, 07:37:54
Last Post: Rusty2009
  Knowledge about my grill needed DE5IRED 3 5,366 19:th-Mar-2015, 18:40:22
Last Post: tucpal

Forum Jump:


Users browsing this thread: 1 Guest(s)