Switch to desktop version  
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Welcome back to the VXOC FORUM. Sorry for our lack of support over the last year but MYBB is back and so are we. Let's get the forum buzzing again... (March 25, 2022) x



Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Tags
check lamp plate warning number

Check Number Plate Lamp Warning
#1
Replaced both blown bulbs this morning and are working fine but the "Check Number Plate Lamp" error is still coming on when ignition turned on. Any ideas?

Cheers
Reply
#2
Sometimes it can take a few starts before it goes away as the BCM has the error stored in memory.

if you replaced them with LED bulbs you will get the error.
Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply
#3
Cheers for your reply, Rusty, I actually sorted it out. Just in case anyone else comes across this it was due to the wrong bulbs. I used 504 (12V 3W) instead of 501 (12V 5W). Even though the bulbs were both working they weren't drawing enough power and so the management system thought they weren't working.
Reply
#4
Glad you sorted it.
Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply
#5
Replaced both bulbs with 501's 3 days ago & lights are both working yet error is still coming up on the dash check number plate light ?
Is there any way I can reset?
Reply
#6
(18:th-Oct-2020, 19:10:07)Galway11 Wrote: Replaced both bulbs with 501's 3 days ago & lights are both working yet error is still coming up on the dash  check number plate light ?
Is there any way I can reset?

Did you replace them with halogen bulbs or LED bulbs?
Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply
#7
(18:th-Oct-2020, 19:10:07)Galway11 Wrote: Replaced both bulbs with 501's 3 days ago & lights are both working yet error is still coming up on the dash  check number plate light ?
Is there any way I can reset?

no replaced like for like .... 501 osram halogen
Reply
#8
That is very strange then, a couple things you can try.

1. Make sure the contacts are clean and holding the bulb tightly.
2. Remove the battery negative for 1hr+ this will allow all systems to fully shut and reboot once reconnected (which can sometimes solve these errors).
Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply
#9
(22:nd-Oct-2020, 19:51:25)Galway11 Wrote:
(18:th-Oct-2020, 19:10:07)Galway11 Wrote: Replaced both bulbs with 501's 3 days ago & lights are both working yet error is still coming up on the dash  check number plate light ?
Is there any way I can reset?

no replaced like for like .... 501 osram halogen

Did you use the correct wattage bulbs? I had some 501's kicking about in my garage but they were only something like 2 watts, and thus I still got the bulb fail warning when I fitted them. IIRC they need to be 5 watt 501's.
Reply
#10
I had a similar problem with a front side light when I had an Astra twintop a few years ago, it only seemed to happen this time of year and found out it was condensation on the connectors
Reply
#11
Cheers. Problem resolved by taking negative terminal for 1 hr
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Inlet air pipe gasket part number. Euroshopper 1 2,154 31:st-Dec-2020, 17:23:19
Last Post: Jpbroad1970
  No sound on indicators, seat belt warning and quiet front parking sensors mpotsb 4 8,336 22:nd-Feb-2020, 19:24:53
Last Post: mpotsb
  Number plates Flick19191 0 1,948 26:th-Sep-2019, 10:54:13
Last Post: Flick19191
  Lacking Power - What can I check everson38 3 3,353 10:th-Jul-2019, 10:44:50
Last Post: Big Dave2
  Tyre Pressure Warning Niggle phlyer 4 5,372 23:rd-Mar-2019, 11:39:36
Last Post: andyp
  Replacing door check strap robk999 5 6,901 7:th-Feb-2019, 21:27:33
Last Post: Telsun
  Licsence plate lights Nathjnz 2 4,180 11:th-Dec-2017, 16:37:25
Last Post: Nathjnz
  Fitted rear led lights, now bulb warning issues twinpipes 3 5,271 27:th-Jul-2017, 21:02:41
Last Post: Hummelshøj
  Number Plate Lights JJ00 1 3,697 15:th-Feb-2017, 21:57:03
Last Post: Wayneofwolves
  Airbag Warning Message sheppy1 7 9,145 25:th-Sep-2016, 21:23:20
Last Post: sheppy1

Forum Jump:


Users browsing this thread: 1 Guest(s)